Only live and valid coupons and
deals updated every few minutes!

Banggood, Amazon, Gearbest, Geekbuying,
Aliexpress, Lightinthebox, Tomtop and many more!

MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer

MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer

Current price:
Banggood: $46.15 (original price: $58.99, discount: 22.0%)
Buy link:Price without coupon:Price with coupon and discount in %:Start time:End time:Coupon code:
MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer

Compatibility

To confirm that this part fits your vehicle, please enter your vehicle’s details below.

  • Year:
    Select

    • Make:
      Select

      • Model:
        Select

        • Submodel:
          Select

          • Trim:
            Select

            • Engine:
              Select

              • Clear All
              This part is compatible with vehicle(s).
              Show all compatible vehicles
              This part is compatible with
              1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  Overview:

                  1. Combine 2560 and ramps1.4 on one board, which solves the cumbersome and troublesome problem of Ramps1.4 combination interface.
                  2. Users can replace the motor drive by themselves, support 4988 drive and 8825 drive, TMC2100 drive
                  3. Can accept 24V input, the same system power can reduce the hot bed current to 1/4, effectively solve the hot bed MOS tube heating problem.
                  4. Using the open source firmware Marlin, the configuration is exactly the same as ramps1.4, which can directly replace Ramps1.4.
                  5. Can directly connect 2004LCD display and 12864LCD display, can support TFT28, TFT32 touch screen.
                  6. 
                  TL-touch is a fully automatic universal 3D printer hot bed leveling probe (automatic leveling probe)
                  Its advantages are simplicity, compactness, high precision, good compatibility, and compatibility with all bed materials, such as glass, metal, wood, plastic, acrylic, etc.

                  About A4988 drive:
                  1, suitable for driving the stepper motor below 8V-35V 2A.
                  2. Only a simple step direction control interface.
                  3, five different stepping modes: full, half, 1/4, 1/8 and 1/16.
                  4, the adjustable potentiometer can control the maximum current output, thus achieving a higher step rate.
                  5, automatic current attenuation mode detection / selection.
                  6. Overheating shutdown circuit, undervoltage lockout and cross current protection.
                  7, grounding short circuit protection and load short circuit protection.
                   
                  3d-touch wiring:
                  Connection 3Pin: Black (-, GND)
                  Red (+ 5V)
                  Blue (control signal)
                  2PIN: Black (-, GND)
                  Yellow (Zmin)
                  Matters needing attention:

                  Pay Attention:
                  1. Please confirm whether the positive or negative is reversed before power-on, the power supply is reversed, and the motor driver board is connected to reverse the possibility of burning the chip and the circuit. Please confirm the power again.
                  2. Please do not plug or unplug the motor and drive when the power is on, it is easy to cause the drive to burn out;
                  3. Also do not adjust the current during motor operation. The correct way is to disconnect the power supply, unplug the motor, re-power it, adjust the potentiometer, and measure the voltage on the potentiometer until the measured voltage is the same as expected. Do not insert the reverse drive, otherwise it will burn out the drive and even burn the motherboard.


                  Package Included:

                  1 x MKS GEN L motherboard
                  1 x USB cable
                  5 x Green A4988 Drive
                  5 x Heat sink
                  1 x TL-touch sensor
                  1x  TL-touch cable
                  1 x 1m 2pin line
                  1 x 1m 3pin line
                  with Screw&
                  Nut
                   

                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer


                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer

                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer


                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer

                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer

                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer
                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer
                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer
                  MKS-GEN L Integrated Controller Mainboard + TL-touch Sensor with A4988 Driver/Heatsink/Lines Kit for 3D Printer

                  We will be happy to hear your thoughts

                      Leave a reply

                      For security, use of Google's reCAPTCHA service is required which is subject to the Google Privacy Policy and Terms of Use.

                      I agree to these terms.

                      Translate »

                      Pin It on Pinterest

                      Logo
                      Turn off snow